What is PEB Structure ?



PEB Structure :- Pre Engineering building (PEB) is pre fabricated steel structure and low cast first construction, This technology used for supper structure of building .

Application PEB Structure :-

  •  Wear House 
  • Parking shad 
  • Passenger terminate building
  • Workshop
  • Railway station 
  • Building 
  • shade
Steel column :- Vertical steel start member are called steel column ,generally used for super structure it may be short column and long column ,sub structure  are RCC and joint by Anchor bolt.


Steel beam:- Horizontal steel start member are called steel beam ,steel beam also called rafter, roof sheeting load and praline load come steel beam.

Z praline:- above beam and connect of another beam is called z praline, z praline not required to paint
 
Sag Rod :- 12mm dia bar two end are thread connect to each praline is called sag rod.

Knoop :- Beam and column cantilever section in steel structure are called Knoop 

GP2 Grouting:-Rcc structure and steel structure joint by anchor bolt and 20mm to 50mm gape are filling by grouting and Gp2 grouting ,like fossroc ,pidilite ,etc

Structure steel testing : various location various type of design and various type of steel section , i am testing report submit but this is example 

Results:               

1.       Tensile Strength:

Name of Materials

Brand/ Specification

Yield Strength

(MPa)

Ultimate Tensile Strength

(MPa)

Method of Testing

SHS 91.5X91.5X3.6

JSW

261

455

IS1608

SHS 180X180X5.0

JSW

257

437

CHS 139.5 OD-4.5

JSW

253

415

SHS 132X132X4.8

JSW

264

463

CHS 88.9 OD-3.2

JSW

252

418

CHS 273.0 OD-8.0

JSW

255

421

CHS 165.1 OD-5.4

JSW

258

440

 1.       Bend Test:

Name of Materials

Brand/ Specification

Bend

Remarks

Method of Testing

SHS 91.5X91.5X3.6

JSW

No visible cracks 

Pass

IS 2329

SHS 180X180X5.0

JSW

No visible cracks 

Pass

CHS 139.5 OD-4.5

JSW

No visible cracks 

Pass

SHS 132X132X4.8

JSW

No visible cracks 

Pass

CHS 88.9 OD-3.2

JSW

No visible cracks 

Pass

CHS 273.0 OD-8.0

JSW

No visible cracks 

Pass

CHS 165.1 OD-5.4

JSW

No visible cracks 

Pass

1.       Flattening Test:


Name of Materials

Brand/ Specification

Bend

Remarks

Method of Testing

SHS 91.5X91.5X3.6

JSW

No visible cracks 

Pass

IS 2328

CHS 139.5 OD-4.5

JSW

No visible cracks 

Pass

SHS 132X132X4.8

JSW

No visible cracks 

Pass

CHS 88.9 OD-3.2

JSW

No visible cracks 

Pass

CHS 165.1 OD-5.4

JSW

No visible cracks 

Pass

 

Comments

Post a Comment

Popular posts from this blog

Number of cubes for concrete as per is code

Image
 Number of cubes for concrete as per is code The minimum frequency of sampling of concrete of the each grade shall be in accordance with the following Quantity of concrete in the work in m 3 Number of sample 1-5 1 6-15 2 16-30 3 31-50 4 51 and above 4 plus one additional sample for each additional 50m 3      Characteristic Compressive Strength Compliance Requirement : Specified grade Mean of the group of 4 non-overlapping consecutive test results in N/mm 2 Individual test results in N/mm 2 M-15 >= fck + 0.825 x established standard deviation (rounded off to nearest 0.5 N/mm 2 ) or fck + 3 N/mm 2 whichever is greater >=fck – 3 N/mm 2 M-20 or above >= fck + 0.825 x established standard deviation (rounded off to nearest 0.5 N/mm 2 ) or fck + 4 N/mm 2 whichever is greater >= fck – 4 N/mm 2 Note : at least one sample taken
Read more

Silt Content Test as per IS Code

Image
Silt Content Test as per IS Code   Take a little sand and rub the same in hand, if palm remain clean it can be assumed that sand is free of silt that called is silt content test . It is hand test. Frequency of testing  Every 20cum or more frequency as decided by engineer in charge  Permissible limit   Acceptance standard -maximum permissible limit silt content shall not be " more than 8%"  as per is code 383 and as per CPWD specification  Note: (i) If silt content is more, corrective action taken should be noted in column 10 and silt content referred after such action  and recorded in the register.             (i) Fine aggregate contenting more silt than allowable percentage shall be washed so that the silt contents are with in prescribed limit for which nothing shall be paid  Test for silt content  The method for determining silt contents is as follows:     A sample of sand to be tested shall be placed with out drying in a 200 ml measuring cylinder the volume of sample shal
Read more

1:2:4 concrete mix calculator

Image
 1:2:4 concrete mix calculator concrete mix1:2:4 mins one is cement and two is sand(fine aggregate) and 4 is stone chip (coarse aggregate) coarse aggregate is two type 10mm and 20mm , 10mm will be 40 percentage and 20mm will be 60 percentage (for batter mixing) 1 cum wet volume =1.53cum dry volume Ratio is 1:2:4=1+2+4=7 cement :  1/7x1.53=0.22/0.035=6.24 Bag =313 kg (cement unit volume 1450=50/1450=0.035) Sand (fine aggregate): 1/7x1.53x2=0.44 cum=15.43cft Coarse aggregate: 1/7x4x1.53=0.87 cum = 30.87 cft 10mm :  0.87x0.40=0.35cum = 12.28cft 20mm : 0.87x 0.60=0.522 cum =18.43cft Water : water cement ratio as per IS 456 0.45 to 0.6 . we  assume 0.5 if plasticizer is not provided=313x0.5=156.5liter (slump maintain for 100mm , if water cement ratio is more and give strength is less so maintain minimum water cement ratio) if plasticizer is used then it will be 0.8 percent of cement =0.008x313 =2.54 liter Note: it is nominal mix M20 grade , its not design mix This type of nominal mix are u
Read more